electronics
cable, in electrical and electronic systems, a conductor or group of conductors for transmitting electric power or telecommunication signals from one place to another. Electric communication cables transmit voice messages, computer data, and visual images via electrical signals to telephones, wired radios, computers, teleprinters, facsimile machines, and televisions. There is no clear distinction between an electric wire and an electric cable. Usually the former refers to a single, solid metallic conductor, with or without insulation, while the latter refers to a stranded conductor or to an assembly of insulated conductors. With fibre-optic cables, made of flexible fibres of glass and plastic, electrical signals are converted to light pulses for the transmission of audio, video, and computer data.
The most common type of electric power cable is that which is suspended overhead between poles or steel towers. These aerial cables consist of a number of wires, usually of copper or aluminum, twisted (stranded) together in concentric layers. Copper or aluminum is chosen for high electrical conductivity, while stranding gives the cable flexibility. Because aerial cables are frequently subjected to severe environmental stresses, alloys of copper or aluminum are sometimes used to increase the mechanical strength of the cable, although at some detriment to its electrical conductivity. A more common design is to include in the stranded cable assembly a number of high-strength, noncorrosive steel wires. Many aerial cables, especially those operating at high voltages, are bare (uninsulated). Cables operating at lower voltages frequently have coverings of asphalt-saturated cotton braid, polyethylene, or other dielectric (nonconducting) material. These coverings offer some protection against short-circuiting and accidental electric shock.
Another type of electric power cable is installed in underground ducts and is extensively used in cities where lack of space or considerations of safety preclude the use of overhead lines. Unlike an aerial cable, a buried cable invariably uses commercially pure copper or aluminum (mechanical strength is not a problem underground), and the stranded conductor is frequently rolled to maximize its compactness and electrical conductance.
Aerial and underground power cables compose a major portion of the electrical circuit from the generator to the point of utilization of the electric power. The balance of the circuit (and sometimes the entire circuit) may, however, require specialized cables. Illustrative of these usages and of the special conditions to be met are cables for use in steel mills and boiler rooms (high temperature), on mobile equipment (vibration and excessive flexing), in chemical plants (corrosion), for submarines and mines (mechanical abuse), near nuclear reactors (high radiation), and on artificial satellites (pressure extremes).
Electric cables used to transmit information are quite different from power cables, both in function and in design. Power cables are designed for high voltages and high current loads, whereas both voltage and current in a communication cable are small. Power cables operate on direct current or low-frequency alternating current, while communication cables operate at higher frequencies. A power cable usually has not more than three conductors, each of which may be 1 inch (2.5 cm) or more in diameter; a cable may have several thousand conductors, the diameter of each being less than 0.05 inch (0.125 cm).
Protective coverings for electric communication cables are similar to those for electric power cables. They usually consist of an aluminum or lead-alloy tube or of a combination of metallic strips and thermoplastic materials. The insulation of a cable is composed of dry cellulose (in the form of paper tape wrapped around the conductor or paper pulp applied to the conductor) or of polyethylene. The insulation thickness is a few hundredths of an inch or less. A coaxial cable, which first gained widespread use during World War II, is a two-conductor cable in which one of the conductors takes the form of a tube while the other (smaller but also circular in cross section) is supported, with a minimum of solid insulation, at the centre of the tube. Several of these coaxial units may be assembled within a common jacket, or sheath.
Are you a student? Get a special academic rate on Britannica Premium.
Learn MoreThe construction of long submarine cables for either or telegraph service is somewhat different from that discussed previously. A transatlantic cable for telegraphs was first completed in and for telephones in ; a fibre-optic cable first spanned the Atlantic Ocean in . See also undersea cable.
If you want to learn more, please visit our website Mingda.
Fibre-optic telecommunication cables optical fibreLight ray passing through an optical fibre.
How underwater cables connect the world's continents
The seabed off Crete is prepared for the laying of an undersea fibre-optic cable.
See all videos for this articleCables made of optical fibres first came into operation in the mid-s. In a fibre-optic cable, light signals are transmitted through thin fibres of plastic or glass from light-emitting diodes or semiconductor lasers by means of internal reflection. The advantages of fibre-optic cables over conventional coaxial cables include low material cost, high transmission capacity, low signal attenuation, data security, chemical stability, and immunity from electromagnetic interference.
Like other types of cables, fibre-optic cables are designed and insulated for various applications overland, underground, overhead, and underwater. Such cables usually consist of a core embedded in a series of protective layers. The cable core contains a single solid or stranded central strength element that is surrounded by optical fibres; these are either arranged loosely in a rigid core tube or packed tightly into a cushioned, flexible outer jacket.
The number and type of protective layers surrounding the core depends upon the use for which the cable is intended. In general, the core is covered with a layer of copper to improve conduction over long distances, followed by a material (e.g., aluminum foil) to block the passage of water into the fibres. Steel wire or strands are added for tensile strength, and the entire cable is then wrapped in a polyethylene sheath, or jacket, for stability. See also fibre optics.
This article was most recently revised and updated by Amy Tikkanen
The cables used for the transmission and distribution of electrical energy cables are called electrical power cables.
It is used for the transmission of extra high voltages in a place. The power cable consists of two or more electrical conductors combined with an over sheath.
Underground cables are more costly than aerial cables. Electricity cables are primarily used for power distribution and transmission.
It is an assembly of one or more electrical conductors that have been individually insulated and are often held together by an overall sheath.
The conductor is used to provide the conducting path for the current.
The dielectric provides the service voltage and isolates the conductor from other objects.
The primary aim of armoring is to protect the current-carrying conductors from electromagnetic interference.
It is also used to earth the cable for security. The sheath is used to avoid contact with moisture entering and protects the cables from all external influences like fire chemical or electrochemical attack. etc.
The company is the world’s best Electric Cable Wire supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.