The information contained herein is the property of LEDiL Oy, Joensuunkatu 7, FI- SALO, Finland and is subject to change without notice. Please visit www.ledil.com for additional information, such as the latest photometric files, 3D mechanical models, and application notes relating to handling, gluing and taping.
For more information, please visit Getian.
Illumination is one of the most critical components of a machine vision system. The selection of the appropriate lighting component for a specific application is very important to ensure that a machine vision system performs its tasks consistently and reliably.
The main reason is that improper illumination results in loss of information which, in most cases, cannot be recovered via software. This is why the selection of quality lighting components is of primary importance: there is no software algorithm capable of revealing features that are not correctly illuminated.
To make the most appropriate choice, one must consider many different parameters, including:
Surface property of the material to be inspected or measured (e.g. color, reflectivity)
Since many parameters must be considered, the choice can be difficult and sometimes the wisest advice is to perform feasibility studies with different light types to reveal the features of interest. On the other hand, there are a number of simple rules and good practices that can help select the proper lights and improve the image quality.
For every application, the main objectives are the following:
Basically, light interacts with materials by being
Additionally, when light travels across different media it refracts, i.e. it changes direction. The amount of refraction is inversely proportional to the light wavelength; i.e. violet light rays are bent more than red ones. This means that light with short wavelengths gets scattered more easily than light with long wavelengths when hitting a surface and is therefore, generally speaking, more suited for surface inspection applications.
In fact, if we ideally consider wavelength as the only parameter to be considered from the previous list, blue light is advised for applications such as scratch inspection while longer wavelengths such as red light are more suited for enhancing the silhouette of transparent materials.
Incandescent lamps are the well-known glass bulbs filled with low pressure, inert gas (usually argon) in which a thin metal wire (tungsten) is heated to high temperatures by passing an electric current through it. The glowing metal emits light on a broad spectrum that goes from 400 nm up to the IR. The result is a white, warm light (corresponding to a temperature of K) with a significant amount of heat being generated.
Fluorescent lamps are vacuum tubes in which UV light is first produced (by interaction between mercury vapor and highly energetic electrons produced by a cathode) and then is adsorbed by the tube walls, coated with fluorescent and phosphorescent material. The walls then re-emit light over a spectrum that again covers the whole visible range, providing a “colder” white light source.
LEDs (Light Emitting Diodes) produce light via the annihilation of an electron-hole pair in a positive/negative junction of a semiconductor chip. The light produced by an LED depends on the materials used in the chip and is characterized by a narrow spectrum, i.e. it is quasi-monochromatic.
A general guideline for computing the peak wavelength of a LED is the following:
LEDs are not natural sources of white light: they emit almost monochromatic light.
There are two main ways of producing white LED light:
The second method is the most popular one, as allows for greater efficiency and a better color rendering compared to an RGB system. To obtain different color temperatures, you can vary the wavelength of the LED, the composition and the thickness of the phosphorus coating.
The choice to use white light in imaging applications should be limited to cases where a true chromatic response is really needed, obviously along with a color camera.
Want more information on IR LEDs for Machine Vision? Feel free to contact us.
In all other cases, the use of white light affects the performance of the optical system, due to the chromatic aberrations that are inevitably generated and due to the loss of resolution of color sensors.
An LED illuminator can be controlled by either setting the voltage V across the circuit or by directly feeding the circuit with electric current I.
One important consideration is that the luminous flux produced by a single LED increases almost linearly with the current while it does not do so with respect to the voltage applied: 1% uncertainty on the driving current will translate into 1% luminance uncertainty, while 1% uncertainty on the input voltage can result in a several percentage points variation (see picture). For this reason, it is suggested to directly regulate the current and not the voltage, so that the light output is stable, tightly controlled and highly repeatable.
For example, in measurement applications, it is paramount to obtain images with a stable grey level background to ensure consistency of the results: this is achieved by avoiding light flickering and ensuring that the LED forward current of the telecentric light is precisely controlled.
LEDs can be used to make continuous light, keeping constant the current flowing through the device.
On the other hand, LEDs can be easily driven in a pulsed (on/off) regime and can be switched on and off in sequence, turning them on only when necessary.
Usage of LEDs in pulsed mode has many advantages:
If the LED driving current (or voltage) is set to the nominal value declared by the LED manufacturer for a certain amount of time and then is reset to zero, we talk about pulsed mode: the LED is simply switched on and off.
LEDs can also be driven at higher intensities (i.e. overdriven) than the nominal values, thus producing more light but only for a limited amount of time: in this case we say that the LED is operated in strobed mode.
Strobing is needed whenever the application requires an increased amount of light to freeze the motion of fast moving objects, in order to eliminate the influence of ambient light, to preserve the LED lifetime and to synchronize the ON time of the light (ton) with the acquisition time of the camera and item to be inspected.
To properly strobe an LED light, a few parameters must be considered (see figure):
When dealing with online applications, there are some important parameters that have to be considered. Specifically, depending on the object speed and image sharpness that is required for the application, the camera exposure time must be always set to the minimum in order to freeze motion and avoid image blurring. Additionally, black and opaque objects that tend to absorb instead of reflecting light, are particularly critical.
As an example, let’s suppose to inspect an object moving with speed vo using a lens with magnification m and a camera with pixel size p.
The speed of the object on the sensor will be m times vo:
For example, using p = 5.5 µm, m = 0.66, vo = 300 mm/s (i.e. a line speed of 10,800 samples/hr on a 100 mm FoV) we find a maximum exposure time of t = 83 µs. At such speed, the amount of light emitted by LED illuminator used in continuous mode is hardly ever enough - so that strobing the illuminator for an equivalent amount of time is the best solution.
Another parameter that we can adjust in order to get more light into the system is the lens F/#: by lowering the lens F/# we will gather more light; however, this will lower the depth of field of the system. Moreover, this might also lower the image quality since, in general, a lens performs better in the center and worse towards the edges due to lens aberrations, leading to an overall loss of sharpness. Increasing the camera gain is another way, however this always introduces a certain amount of noise, thus again leading to a degraded image where fewer details can be distinguished.
As a result, it is always a good practice to choose sufficiently bright lighting components, allowing you to correctly reveal the features of interest the inspected of object when used in combination with lenses set at the optimum F/# and without the need to digitally increase the camera gain.
If you are looking for more details, kindly visit UV LEDs for 3D Printing.